1995-2004 Toyota Tacoma Standard Rear Leaf Springs
Our ’95-’04 Tacoma rear leaf springs are a direct fit for the ’98-’04 Tacoma. They will also fit the ’95-’97 Tacoma with modifications to the spring hangers (see note below). These springs have a special torque leaf to reduce axle wrap. Springs come with new poly bushings and sleeves.
Note: Mounting our springs on 95-97 Tacomas will require new front spring hangers 2″ forward (hole to hole) from stock, and the rear shackle hangers moved back 1″.
All-Pro’s Standard Duty leaf springs (4500T-AP) are NOT designed for heavy weight carrying capability. They are designed for ride quality and flex. For those carrying heavier loads such as rigs fully loaded for long-term expeditions, we recommend All-Pro “Expedition” Heavy Duty rear springs.
All-Pro’s new Expedition leafs are specifically designed to combine off-road performance with heavy duty weight carrying capacity. The popular expedition style trend in off-road vehicles is resulting in trucks that are carrying heavier loads than normally seen off-road. Specialized long-distance excursion gear such as roof-top tents, recovery and repair gear, camping equipment and extra water and fluids can add significantly to the cargo weight of expedition vehicles, exceeding the intended operating parameters of typical performance leaf springs.
All-Pro’s Expedition Leaf Springs (4500T-AP-EX) feature a 20% higher spring rate than our standard leaf springs. They are otherwise identical in dimension and quality, providing the same eye-to-eye measurements and wheel travel.
On unloaded Tacoma’s, they will result in a 1″ taller stance than the stated lift height of 3″. The stated lift height is maintained with loads of 400-500 lbs of cargo.
* A higher number of thinner leaves provides a smoother, progressive spring rate compared to fewer, thicker leaves
* Double “military” wrap provides extra strength for the main leaf
* “Torque Leaf”, an extra half-leaf at the top of the spring pack, increases anti-wrap properties without hindering travel or ride quality
* Diamond-cut leaf ends to eliminate stress points which may weaken leafs and lead to premature failure
* Teflon anti-friction pads between leafs provide smoother flex, lessen spring wear and reduce noise
* Leafs are shot-peened after forming to relieve stress
* Every completed spring pack is pre-cycled to their travel extremity for quality control and to reduce the likelihood of initial sag
* Comprehensive 12-month warranty for non-racing applications when properly installed
Standard Duty Leaf Spring Specifications:
– Number of Leaves: 7 + 1 Overload/Rebound
– Eyelet-to-Eyelet Length (Free): 51-5/8″ (1311 mm)
– Spring Rate: 154 lbs/in
Expedition Leaf Spring Specifications:
– Number of Leaves: 6 + 1 Overload/Rebound
– Eyelet-to-Eyelet Length (Free): 51-1/4″ (1302 mm)
– Spring Rate: 207 lbs/in
Use of lifting blocks or shackle flip kits void all warranty on All-Pro Leaf Springs
Standard Duty Leaf Spring Specifications:
- Number of Leaves: 7 + 1 Overload/Rebound
- Eyelet-to-Eyelet Length (Free): 51-5/8″ (1311 mm)
- Spring Rate: 154 lbs/in
Expedition Leaf Spring Specifications:
- Number of Leaves: 6 + 1 Overload/Rebound
- Eyelet-to-Eyelet Length (Free): 51-1/4″ (1302 mm)
- Spring Rate: 207 lbs/in
- 1995-2004 Toyota Tacoma (requires modifications to fit 1995-1997 Toyota Tacoma)
ALL-PRO products are warranted to be free from defects in materials and workmanship prior to installation. Any alteration, improper use, or modification will void this warranty. This warranty is extended by All-Pro to the original purchaser. This warranty is effective for 90 days from the date of purchase. Any description of the goods is for the sole purpose of identifying them, is not a part of the bargain, and does not constitute a warranty that the goods will conform to that description. Any sample, model or advertised item is for illustrative purposes only, is not part of the basis for the bargain, and is not to be construed as a warranty that the good will conform to the sample, model, or advertised item. No affirmation of fact or promise made by All-Pro will constitute a warranty that the goods will conform to the affirmation or promise.
Purchasers and users of our products are responsible for determining the applicability of a product to their specific application. In the event of a defect, malfunction, or failure to conform to this warranty, All-Pro will repair or replace the goods without charge within 30 days of receipt of goods. If All-Pro is unable to replace and/or repair the goods or if All-Pro, at its sole discretion, determines that neither option is commercially practicable or cannot be made within 30 days of receipt of the goods, All-Pro will refund the purchase price. The purchaser is responsible for installation and removal of all parts, freight or shipping costs, and incidental or consequential damages.